Miscellaneous

How do I set up cambium?

How do I set up cambium?

Modified on: Mon, 4 May, 2020 at 4:30 PM

  1. Step 1 – Login to the Router.
  2. Username: admin.
  3. Password: admin.
  4. Step 2a – Configure the WAN Interface (PPPoE with VLAN10)
  5. Step 2b – Configure the WAN Interface (DHCP with VLAN10)
  6. Step 3 – Secure the Router.
  7. Step 4 – Optional; Configure the Timezone & NTP (Network Time Protocol)

How do you set a point to point in cambium?

Login to the radio and install the latest firmware image. You will need to reboot the radio once the firmware file uploads. Login back into the radio and navigate to Configuration – Radio. Here you select Access Point, Country and an SSID of your choice (These need to be the same on both Radio).

How do I validate a subscriber module installation?

To verify that the correct device has registered, navigate to Monitor -> Wireless and validate the Registered Subscriber Modules list. For further verification of the link, navigate to Tools -> Wireless and run a wireless link test to determine the capacity of the link.

How do I reset cambium ePMP 1000?

Resetting the ePMP to factory defaults by power cycling Reconnect the Ethernet cable to re-supply power to the ePMP device for at least 30 seconds and allow it to go through the boot up procedure (Note: Device will go through an additional reset automatically).

What is the default IP address for the subscriber module?

The factory default IP address is either 192.168. 0.1 (AP mode) or 192.168. 0.2 (SM mode).

How do I reset my cambium router?

Hard reset option ‘RST’ in R201

  1. While device is powered on and booted up, please insert a pin in the ‘RST’ hole and gently press for 10-15 seconds and remove the pin.
  2. After removing the pin wait for 25 – 30 seconds and observe LED’s, we will noticed that all LED’s will blink together and device will reboot now.

What should configuring the ePMP radio max range be set to?

The ePMP software is optimized to a max distance of 40 miles (64 km).

What is SM cambium?

cnRanger Subscriber Module (SM) The cnRanger™ Subscriber Modules (SM) are highly compact and cost-effective LTE Customer Premise Equipment (CPE) designed for ease of installation, onboarding, management, and monitoring.

What is a valid way to factory default an ePMP radio?

Answer: There are 3 ways to factory default the ePMP radios: 1) By pressing the power reset button (using a paper clip) for about 10 seconds. 2) Via a remote power on/off sequence executed by pulling the power/Ethernet cable to the unit.

How do I default my cambium radio?

Or if you are still able to access the radios GUI remotely, you can Factory Reset the unit under Tools-> Backup/Restore -> Reset To Factory Defaults.

What is the IP address of cambium?

With Cambium EPMP radios, the default management IP addresses are 192.168. 0.1 for Accesss Point Radios and 192.168. 0.2 for Client/CPE Radios.

What is the default IP address for cambium?

What is the default password for cambium router?

Enter the default username as admin and password as admin. Change the default password by navigating to Administration > Management > Password Reset option. The default WAN IP Mode is DHCP.

How do I log into cambium router?

Default Access Parameters

  1. Default IP address: cnPilot R200/200P : 192.168.11.1.
  2. Login: Username : admin.
  3. Command Line Access: Telnet : Disabled by default, need to be enabled from Web UI.
  4. Web GUI Access:
  5. Default SSID and Password:
  6. Default SSID’s in 2.4/5 GHz.
  7. Default Secuity / Password:
  8. Default Radio Status:

What does ePMP GPS synchronization use for timing?

A stable timing source is utilized by every AP in the system to precisely synchronize the start of every transmit and receive cycle within the TDD framing structure used in the Cambium Networks ePMP solution.

What is the default max range value on AP?

The AP will reject any SM network entry attempts from outside the configured maximum range. Default value is 3 miles.

How do I reset my cambium radio?

What is the default IP of cambium?

192.168.0.1
The factory default IP address is either 192.168. 0.1 (AP mode) or 192.168. 0.2 (SM mode). Press ENTER.

How do I access my cambium router?

Connect to the wireless router by typing http://192.168.11.1 in web browser. Enter the default username as admin and password as admin. Change the default password by navigating to Administration > Management > Password Reset option. The default WAN IP Mode is DHCP.

How do I access a cambium router?

Select these options Use the following IP address and Use the following DNS server addresses to obtain IP address and DNS server addresses automatically. Connect to the wireless router by typing http://192.168.11.1 in web browser. Enter the default username as admin and password as admin.

Who should use the cambium ePMP series?

This guide describes the planning, installation, configuration and operation of the Cambium ePMP Series of point-to-multipoint wireless Ethernet systems. It is intended for use by the system designer, system installer and system administrator. For radio network design, see: •Product description •System hardware •System planning

What are the ePMP 1000 connectorized radio environmental specifications?

Table 32 ePMP 1000 Connectorized radio environmental specifications Category Specification Temperature -30°C (-22°F) to +55°C (131°F) Wind loading 118 mph (190 kph) maximum. See ePMP 1000 Connectorized Radio wind loading on page 62 for a full description. Humidity 95% condensing Environmental IP55 CAMBIUM NETWORKS 026v031 62

Where is cambium ePMP located?

Address: Cambium Networks Limited, 3800 Golf Road, Suite 360 Rolling Meadows, IL 60008 Purpose Cambium Networks ePMP documents are intended to instruct and assist personnel in the operation, installation and maintenance of the Cambium ePMP equipment and ancillary devices.

What is the Poe input size for Cambium 10/100/1000 BASE-TX?

Ethernet RJ45 PoE input 10/100/1000BaseT, Compatible with Cambium PoE pinouts (V+ = 7 & 8, Return = 4 & 5) and Standard PoE pinouts (V+ = 4 & 5, Return = 7 & 8) 10/100 Base-TX Ethernet Management and data Reset Button Physical button N/A For resetting the radio and for setting the radio back to its factory default configuration. See

https://www.youtube.com/watch?v=W8fbt7bbXTw